Home Page | Owners Registry | Discussion Forums | ProwlerMall | Event Scrapbooks | About |
Click here to return to the Prowler Online Board Main Page |
ProwlerOnline, Plymouth/Chrysler Prowler Discussion Forum
General Prowler Discussion front sway bar links-replace or not?
|
Bottom of Page | next newest topic | next oldest topic |
Author | Topic: front sway bar links-replace or not? |
scooter1 POA Site Supporter Prowler Junkie From:Southeast WI, USA |
posted 05-29-2007 06:39 PM
Well, a couple weeks ago "Quincy" sent me a set of front sway bar links to see if it was possible to replace the upper end bushings with polyurethane inserts. This is the Reader's Digest version of what I discovered about these links: -after removing the seals and "degreasing" the insides of the upper ends (typically the seals tend to rot off/crack/leak and look nasty, so people replace them), I found the links to be your basic nylon insert type rod-end. The lower link end seals were in good shape.I believe the lower seals are of a more "plastic" type material. -They are pressed together, so it's really not possible to replace them with polyurethane inserts without destroying them in the process. -After inspecting the links, looks to me that having them sealed is kinda a waste of effort. They have full nylon inserts and the actual relative movement at the upper end of the link is almost none (rotate 15-20 deg back and forth or so, maybe). -I see no reason why they could not be used "as is" (without seals or lube) for many years to come. Rod ends typically sold with nylon inserts are meant to be used "as is" in hostile environments and run dry w/no lube. (been in the mechanical design business for 30+ years and this is typical from what I've seen). -I did purchase a set of polyurethane tie rod end seals to try a fit (early VW beetle application, my other sickness), but they don't quite fit. I would guess with a little experimentation, some tie rod seals could be modified to fit, if you really wanted to have seals. -soooooo anyway, in conclusion, when my seals finally rot/crack/leak, I will not be replacing the links (unless they are actually loose inside, not likely). I'll remove the seals, degrease and re-install them as they are and save the big bucks to take the wife out to dinner . Quincy, if you want these back, let me know and I'll ship them to you. They don't show any wear from what I can tell, i.e. they are still nice and tight (probably have another 100thou miles of life left in them.....) This message has been edited by scooter1 on 05-29-2007 at 06:52 PM |
1buddyc POA Site Supporter Prowler Junkie From:San Antonio Texas USA |
posted 05-29-2007 06:48 PM
Thats kind of what I thought...Very useful info. Thanks for doing the R&D, scooter1. |
quincy POA Site Supporter Prowler Junkie From:Fairfield Glade, TN. USA |
posted 05-30-2007 12:30 PM
scooter1, Glad to have been of some assistance. I appreciate you digging into the nitty gritty details of this "premature dust boot failure". (the ones I sent you only have 6,000 miles on them) I tend to agree that the grease/dust boot is overkill for what the actual function of the joint is designed for. I installed my new struts along with Larry Lord's 'Wonder Bar' at the same time....had to take them off anyway for the new stabilizer bar. Please feel free to keep the 'old' ones for your personal use! If and when my new ones blow the seal, I will just silicone the dust boot as a 'boot strap' repair, which will work just fine! |
Orange Power Prowler Enthusiast From:Edmond,OK,USA |
posted 03-05-2013 11:55 AM
I just noticed this on my 2001 Prowler with 17k miles while putting in the WonderBar. So, just remove the boots, degrease and bolt back together? |
Larry Lord Prowler Junkie Personal ScrapBook From:Colton, CA |
posted 03-05-2013 01:00 PM
Oops! This message has been edited by Larry Lord on 03-05-2013 at 01:17 PM |
Larry Lord Prowler Junkie Personal ScrapBook From:Colton, CA |
posted 03-05-2013 01:02 PM
Thanks Scooter and Quincy for the help and the comments. I've told many people for quite some time, to do just this. There is little movement in the area, a little anti-seize might work well to keep things loose. |
alrtg POA Site Supporter Prowler Junkie From:Westminster, MD, USA |
posted 03-05-2013 04:28 PM
I have thought along the same lines about these and had considered trying to find an aftermarket piece much like a tie rod end replacement boot from the local auto parts store but have not yet gotten around to it. THANKS for the information, It is appreciated! |
padroo POA Site Supporter Prowler Junkie From:Chesterton, IN, USA |
posted 03-05-2013 05:08 PM
If memory serves me correctly Beachcat had a homemade cover to seal them but I agree it isn't a big deal one way or the other. |
ed monahan POA Lifetime Site Supporter Prowler Junkie Personal ScrapBook From:Cincinnati, Oh, USA |
posted 03-05-2013 05:21 PM
http://www.prowleronline.com/ubb/Forum2/HTML/003336.html |
All times are CT (US) Top of Page Previous Page | Return to General Prowler Discussion next newest topic | next oldest topic |
All material contained herein, Copyright 2000 - 2012 ProwlerOnline.com
E-Innovations, LP