Home Page | Owners Registry | Discussion Forums | ProwlerMall | Event Scrapbooks | About |
Click here to return to the Prowler Online Board Main Page |
ProwlerOnline, Plymouth/Chrysler Prowler Discussion Forum
General Prowler Discussion Are all interior door panels the same??
|
Bottom of Page | next newest topic | next oldest topic |
Author | Topic: Are all interior door panels the same?? |
shrtdog Prowler Newbie From:Goodyear, AZ |
posted 07-14-2010 12:14 PM
Wondering if all door panels are the same color/configuration from '97-2002. I need a drivers door panel for a 2000 and all I can find at new car dealers are 2002 Chrysler panels. I'm assuming they are all the same, please advise!! Thanks! |
idive POA Site Supporter Prowler Junkie From:Texas USA |
posted 07-14-2010 12:54 PM
I believe all the door panels are the same 97-2002. There MAY be a minor shade difference in color but I don't think there was. If there is it would be negligible. I do know that the wiring connection to the window/door lock switches are different in the 97 than they are in the following years. The 2000 door trim panel part numbers are: 0MB10LAZAD Right side 0MB11LAZAD Left side The 2002 part numbers end in AE This message has been edited by idive on 07-14-2010 at 01:06 PM |
shrtdog Prowler Newbie From:Goodyear, AZ |
posted 07-14-2010 06:51 PM
Thanks for the info! |
catfish POA Site Supporter Prowler Junkie From:scottsdale,az,usa |
posted 07-14-2010 07:35 PM
they are all the same.whats wrong with yours. ------------------ |
shrtdog Prowler Newbie From:Goodyear, AZ |
posted 07-15-2010 01:32 PM
Had door speakers installed and the brainiac who put them in got glue all over it when he tried to glue my handle bezel back on! |
alrtg POA Site Supporter Prowler Junkie From:Westminster, MD, USA |
posted 07-15-2010 03:22 PM
Check your seats closely also just in case the brainiac had a screwdriver in the back pocket as well. |
catfish POA Site Supporter Prowler Junkie From:scottsdale,az,usa |
posted 07-15-2010 05:20 PM
i dont suppose you know what kind of glue he used? the handle bezels are expensive,and have 4 tabs that hold them on.you cannot use glue to install them,they wont stay.sounds to me like they owe you 2 bezels at 80.00 a piece.sounds like they had no idea on how to remove them.if they used a plastic type glue,you may be screwed.id try some cheap lacquer thinner to remove the glue,it may soften it up enough to remove it.use it sparingly and see what happens.the bezels slide str.backwards to remove.you cannot pry on them,they will break.part #s are.tt06dx9aa-rt and tt07dx lt.good luck ------------------ |
shrtdog Prowler Newbie From:Goodyear, AZ |
posted 07-15-2010 05:40 PM
the drivers side bezel tabs were already broken off and it had been glued previously but obviously the person that glued it the first time knew how to do it w/o ruining the door panel! The passenger side had all of the tabs intact so there were no issues. Hindisght being 20/20 I should have just told him to leave the bezel off and replaced it with a new one. I tried goof off, goo gone, fingernail polish remover, etc., that glue won't budge. Luckily they're going to do the right thing and provide me $ to replace the door panel. Thanks for all of the feedback! |
All times are CT (US) Top of Page Previous Page | Return to General Prowler Discussion next newest topic | next oldest topic |
All material contained herein, Copyright 2000 - 2012 ProwlerOnline.com
E-Innovations, LP