Home Page | Owners Registry | Discussion Forums | ProwlerMall | Event Scrapbooks | About |
Prowler Products By Gary | Tom Mills / Jefferson Auto |
Bottom of Page | next newest topic | next oldest topic |
Author | Topic: Alternator |
thomas leuschner POA Site Supporter Prowler Junkie From:e.islip,ny.,usa |
posted 04-28-2009 03:58 PM
With the motor running and a VOM across the battery terminals I am reading 11.91 volts. Sunday when I was driving home from a cruise my check gauge light came on. I noticed the volt gauge was reading below 12 volts. When I got home I turned the Kat off and then on. The check gauge light went off but the volt gauge still reads below 12 volts. Battery is new (less than 6 months)and is kept on a battery tender. Is it possible the alternator clutch went bad. Where is the best place to get a new or rebuilt alternator. Tom |
catfish POA Site Supporter Prowler Junkie From:scottsdale,az,usa |
posted 04-28-2009 06:45 PM
alt.should be charging 13.8 volts,ck.output of alt.not batt voltage. ------------------ |
phil2237 POA Site Supporter Prowler Junkie From:PLACENTIA CALIFORNIA |
posted 04-28-2009 07:44 PM
Thomas, The easy way to test this...Start your Prowler, Then disconnect either one of the battery cables. If the car continues to run, the Alternator is GOOD. If the engine dies out, Replace the alternator, They are available thru most auto parts stores.They run appox $ 180.00 exchange. This message has been edited by phil2237 on 04-28-2009 at 08:18 PM |
Jim S POA Site Supporter Prowler Junkie From:Oak View,Ca. |
posted 04-28-2009 09:02 PM
One other thing to look at is the positive wire on the alternator itself. There have been several that have burnt off at the wire connector at the alternator. New wire end and good to go. |
catfish POA Site Supporter Prowler Junkie From:scottsdale,az,usa |
posted 04-28-2009 09:10 PM
the alt.wire is a fusible link,if you replace make sure you get the same size wire.you can tell if the fusible link has gotten hot,it will have a burned look to it.replace both,end and link ------------------ This message has been edited by catfish on 04-28-2009 at 09:15 PM |
Jim S POA Site Supporter Prowler Junkie From:Oak View,Ca. |
posted 04-28-2009 09:54 PM
Jan, The ones I have repaired have all been the connector only, fusible link is still good. Not sure what the cause is, as the nut is tight, unless the factory crimp was not good. |
thomas leuschner POA Site Supporter Prowler Junkie From:e.islip,ny.,usa |
posted 05-01-2009 01:32 PM
Done, alternator repaired. Don't want to do it again. I tested the alternator at the battery output lead like catfish said and got 11.91 volts, thus proving I had a bad clutch at the alternator pully. I changed the clutch to a pully and I am good to go. Total cost $24.00. Tom |
catfish POA Site Supporter Prowler Junkie From:scottsdale,az,usa |
posted 05-01-2009 07:07 PM
tom,do you have the pulley part#.thanks ------------------ This message has been edited by catfish on 05-01-2009 at 07:08 PM |
thomas leuschner POA Site Supporter Prowler Junkie From:e.islip,ny.,usa |
posted 05-01-2009 08:20 PM
I will get it for you Monday. Tom |
All times are CT (US) Top of Page Previous Page | Return to Technical Questions & Answers next newest topic | next oldest topic |
All material contained herein, Copyright 2000 - 2012 ProwlerOnline.com
E-Innovations, LP